Jacuzzi Error Code Fl1
DO NOT GET INTO THE WATER. Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. The J-315 is similar to the J-325 but has more jetting for more water movement. Could be a dirty filter, a clogged impeller, closed valve, or a piece of plastic film covering the spa drain. navigate here
No corrective action is necessary. Back to Top gFI or GFCI FAILURE Message The Control System Could Not Trip the "GFCI" (gFI).The spa has determined that a GFCI is NOT properly installed in the circuit providing Open the spa cover to allow excess heat and steam to escape. Summer Logic “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather.
Jacuzzi Error Code Fl1
Condition can cause injury or damage to spa and its components. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional. The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2. Press Any Button to Reset and Clear the Error Message.3.
- Do not attempt to service on your own.
- Do not attempt to service on your own.
- Power failure.
- In rare cases (usually warmer climates), the circulation pump may also cause overheating.
- If all these test are checked and they did not solve the error code issues, then it is possible you have a defective hi limit sensor.
- ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement
The low speed pump or circ. Remove the Spa Cover and allow Sanitizer to Dissipate, or do a Partial Water Change.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never Press any button to reset after the problem has been corrected, or or contact your Dealer or Service Organization. 1. How To Fix Flo Error Hot Tub This must be repaired only be a Sundance Spas dealer or qualified service technician.
Back to Top rCA or CHANGE MINERAL CARTRIDGE Message Time to "Change Mineral Cartridge Reminder" (rCA)Install a New Mineral Cartridge per Manufacturers Instructions. Contact your Dealer or Service Organization. Back to Top rPH or CHECK PH Message Time to Check "pH Level Reminder" (rPH).Appears Every 7 Days*. Too Many Closed Jets.6.
This could indicate poor flow or air bubbles in the heater. Hot Tub Error Code Oh The J-355 has a small but good step to enter the hot tub. Summer Logic “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather. No Automatic Functions will turn ON during this time, and the Heater will Not Start.
Balboa Hot Tub Error Codes
Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in Jacuzzi Error Code Fl1 Spa error codes can be somewhat cryptic, but when you have the BIG LIST of CODES, you can immediately define the two or three digit source of trouble. Vita Spa Error Codes I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address
Check for proper spa water level and ensure pump is primed. check over here The J- 315 features two bucket seats and a lounge. On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 30 Days, but some Spa Brands or Models may be Different. Marquis Spa Error Codes
Condition can cause injury or damage to spa and its components. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. OH One of the sensors detected that the water in the hot tub is 112°F (44°C). http://nzbsites.com/error-code/how-to-fix-error-code-36.html BLB (Flashes in between water temperature and “blb”) Indicates that spa needs a new UV bulb.
Back to Top OHH, HH, or HTR TEMP LMT SERVICE REQD Message There is an "Over Heated Heater" (OHH or HH) Condition.One of the Water Temp Sensors has detected 118°F (47.8°C) Great Lakes Hot Tub Error Codes If there is No Error Message, Select "No Error Message" Below. Spa may be partially deactivated or low speed pump (and air blower if equipped) may activate to lower temp OHH Overheat.
Back to Top rtC or RTC FAILURE Message The "Real Time Clock" (rtC) Cannot be Read.At Power-Up, the System Board Real Time Clock could Not be Read.
Freeze Protection The spa system has detected a potential freeze condition. Remove the spa cover and allow the water to cool. Try Turning the Power OFF and back ON again, or Continue for a Detailed Test Procedure.1. Jacuzzi Error Code 616 Emergency Shutdown The system has detected that spa water temperatures are above acceptable safety limits.
Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Purchase new UV bulb from dealer and reset countdown timer. weblink The spa system’s ability to cool itself down is directly affected by ambient temperatures.
Sn2 Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning. Too Many Closed Jets.6. No action needed.Note: It isn’t possible to control the pumps manually while the Freeze condition is running. These error codes are similar to the ones previous, however we will be looking at these at another angle.
b) Hold a garden hose over filter cartridge wall fitting and utilize a rag to make a seal around hose end. The alphabetical list of hot tub error codes below covers all major manufacturers of spa controls, including ACC, Balboa, Brett Aqualine, CTI, Dream Maker, EasyPak, Gecko, Hurricane, Jacuzzi, Len Gordon, Maax, Closed Slice Valve.7. Reset the countdown timer when finished.
Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. Communication between control panel and/or remove control panel and circuit board is faulty. If there is Now a Message Other than a "rtC" or "RTC FAILURE" Real Time Clock Error Message, that Message will Now have to be Diagnosed. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.
Balboa Control Manufacturer Scroll past Common Error Codes for: What common codes actually mean and what you can check prior to scheduling service Common Spa or Hot Tub Error Contact ACC. Hence the need for the BIG LIST of CODES. Then continue on to the next pump.- If the display exits Priming Mode and shows dashes or a temperature or a mode indication (such as Std or Ecn or SLP) before
© Copyright 2017 nzbsites.com. All rights reserved.