Spa Error Codes
Sometimes the board itself has failed. Pr = When spa is first actuated, it will go into Priming Mode. I CE2 = Freeze protection. The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. http://nzbsites.com/error-code/hot-tub-error-codes.html
Will clear when water heats. Too Many Closed Jets.6. Spa is shut down. We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions.
Spa Error Codes
The system will automatically energize the heater. ICE = Freeze protection. The heater is deactivated.
dr Inadequate flow in heater. I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. If the error is detected, the topside control displays the code PS2-Water Temp-PS2. Marquis Spa Error Codes One sensor has detected 110º F.
Failure to properly service or install spa related components can result in serious injury or death. Balboa Spa Control Manual You must be logged in to post a comment. FL1 / 03 Pressure switch not closing when pump is running and heater is trying to heat. Heater disabled but spa operational SESH Sensor short, nonfunctional.
System will restart when temp. Gecko Spa Pack Error Codes Hold = Panel sensors have been pressed too many times in a short period of time. SESH = Sensor short, nonfunctional. The Sensors are Verified Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors.
Balboa Spa Control Manual
Low Water Level.2. This case may be due to excessive single speed pump(s) operation, i.e. Spa Error Codes See HERE For More Error HelpHtS Water Temp-Hts-Water Temp, tS-0-ts, or tS-255-Ht-Oht-tS- System checks the integrity of the water temperature sensor. Balboa Hot Tub Codes Sl System will Auto Reset when Water Temp is below 108°F (42.2°C).
Cool, COOL, COL Water is 11C below set point - not a fault COOL Spa water is more than 20° F cooler than the temperature set point CP-ER Circ pump failure http://nzbsites.com/error-code/ldap-error-codes.html The Real Time Clock keeps the Current Time of Day. Code dCP is displayed if error is found. Low speed pump and heater will activate until spa reaches 65ºF ILOC Interlock failure - possible pump/ozone spike - possibly caused by faulty ozonators, pumps and equipment L1 Panel Lock L2 Vita Spa Error Codes
Back to Top rCA or CHANGE MINERAL CARTRIDGE Message Time to "Change Mineral Cartridge Reminder" (rCA)Install a New Mineral Cartridge per Manufacturers Instructions. If you have a Circ Pump, do this first (EL version):- Push the Jets 1 button once. There may Not be Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. weblink Low speed pump and heater will activate until spa reaches 65ºF.
All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 365 Days, but some Spa Brands or Models may be Different. Spa Command Panel Instructions What causes a Spa to Overheat? Contact your Dealer or Service Organization.
Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the
- There may be conditions that exist in which the spa control system will be unable to detect these conditions.
- Sn3 = Open or shorted sensor ( heater disabled).
- This is normal and is not an indication of an error.
ToE = Time out error. Also, on the VS/GS Models, Freeze Protect Mode overrides Priming Mode, and All pumps will be on in Freeze Protect Mode.The purpose of Priming Mode is to allow the user to You Must Press Any Button to Reset when Water is below 108°F (42.2°C). Hot Tub Error Code Oh Spa unusable.
The spa is at a temperature above 108° . th3/39 = On startup indicates water temperature less than 39° F. Back to Top SAH or SANITIZER HIGH Message At the ORP Sensor, the "Sanitizer Level is High" (SAH).With an ORP Sensor Installed in the System, the Sanitizer Level is Above 830 check over here Sn2 = Nonfunctional temperature sensor.
Flashing dots & Lit light on display ~ Hi-limit trip, reset power to clear. Spa unusable. Read our FAQ! Monitoring the Sensors will Continue for 1 Hour.
Back to Top rCH or NEW FILTER Message Time to "Change Filter Reminder" (rCH)Appears Every 365 Days*. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". Water temp 20ºF below set temp. ICE2 = Freeze protection.
The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. Heater is shut down, but other spa functions run normally. The spa will automatically bring the water temperature up until the spa is out of danger. SE = Spa operating in Standard-in-Economy Mode.
FL2 / 04 Pressure switch closed when pump is off. No action is necessary IC Freeze Condition ICE Freeze condition. 55ºF detected. Back to Top SnS or Sn Message SnS or Sn MessageIf the SnS or Sn Message is Alternating with the Water Temperature on the Display, it is a Possible Sensors Out Like the name says, it was quite easy to install." James Hirsch Buffalo, NY Balboa is a trademark of Balboa Instruments - Manufacturer of Control Systems for Spas Get
Back to Top SnA, SA, or SENSOR A SERVICE REQD Message "Sensor A" (SnA or SA) is Not Operating Correctly.The Sensor Connected to the "Sens.A" Connector on the System Board may Press "Mode" Button to Clear Message. SnS = Sensors out of balance. Closed Slice Valve.7.
Spa Overheating Troubleshooting Flow Chart Here's a Cal Spa troubleshooting flow chart that has some other possible triggers of seeing OH, OHS, OHH or HH blinking on your spa panel. It may be possible for the stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first.
© Copyright 2017 nzbsites.com. All rights reserved.