Solaris 10 Error Last Trap Memory Address Not Aligned
This may be an indication of a network problem, or it may indicate a software configuration problem on the client. I tried the ISO yesterday, and it still failed. NFS write failed for server ... Here is what I did (for information only, use at your own risk) which is pretty straight forward: -make a note of your boot-device 1. http://nzbsites.com/solaris-10/how-to-enable-ftp-in-solaris-10.html
Graphics problems mainly occurred on Blade 10 when I was last involved, but that wasn't the fix. Its search feature can be used to look up key words in an error message to look for current bug reports and patches that may resolve them. Any suggestions? Command not found: This is a C shell error message that means exactly what it says. http://unix.ittoolbox.com/groups/technical-functional/solaris-l/error-last-trap-memory-address-not-aligned-3942113
Although this error message states that the system must be restored from backup, the system is actually fine, and it can be upgraded successfully using the workaround. The information may be useful in examining the source code. Connection reset (ECONNRESET): The target system forcibly closed an existing connection.
- Cheers, Chris.
- Solaris Interactive Text (Console session) 5.
- For example: luxadm -e forcelip /dev/cfg/c99 c99 is the specific controller that is being used to communicate with the tape transport.
- Loaded kernel version 2.6.15 Loading initial ramdisk (6405187 bytes at 0x3E002000 phys, 0x40C00000 virt)...
- Check the possible hardware and SCSI configuration issues before attempting to recover the superblock using the methods listed under BAD SUPER BLOCK above.
- At this point, I fiddle with the OBP settings, and issue a `boot net -p`, it continues, and it actually gets to an install screen!
- In Solaris, interrupts are handled by dedicated interrupt-handling kernel threads, which use mutex locks and semaphores.
- ieN no carrier: The carrier detect pin died during a packet transmission, resulting in a dropped packet.
wrong magic number: See “Corrupt label” above. After many attempts I've successfully installed Ubuntu Server 6.10 using only the cdrom image. You're now being signed in. I've set up a tftp server and placed a boot.img (http://archive.ubuntu.com/ubuntu/dists/dapper-updates/main/installer-sparc/current/images/sparc64/netboot/2.6/boot.img into the /tftpboot filesystem on the server.
ether_hostton: Bad file number/Resource temporarily unavailable: These messages may be a result of a mis-matched nodename file. Check the network connection and make sure that the NFS server is sharing the directory to the client as expected. Either the child exited improperly or failed to start. their explanation Make sure that LD_LIBRARY_PATH is set properly.
Make sure that the Jumpstart configurations and file shares are correct. If you need more information ask me. It may be necessary to change the passwd entry for this user to assign a valid shell. Some patches do require you to upgrade your firmware at the same time.
Booting from the CD image I get this error: boot: expert Allocated 8 Megs of memory at 0x40000000 for kernel Uncompressing image... The result of a calculation is not representable in the defined data type. Check the msgctl(2), semctl(2) or shmctl(2) man page for more details. Sparc cd has been re-released (see ubuntu-announcement) due to fuck up in the release script.
They are delivered to the process that caused the signal. http://nzbsites.com/solaris-10/solaris-10-ssh-offline.html In openboot, type: setenv boot-device cdrom 3. Network dropped connection because of reset (ENETRESET): The remote host crashed or rebooted. So it might be the version of SILO that is at fault here; or perhaps something different with the way initrd is handled.
But I'm not sure if there is really something wrong with the hardware or firmware itself. Consequently, the bulk of remap_kernel() dies as does the entirety of arch/sparc64/prom/map.S We try to share some strings in the PROM library with the ones used at bootup, and while we're done Booting Linux ..
See Core File Management.
Once we are done, we need to re-install the bootblock: cd /usr/platform/`arch -k`/lib/fs/ufs /usr/sbin/installboot ./bootblk /dev/rdsk/c#t#d#s# BAD TRAP: The causes for bad traps include system text errors, data access faults, data This error indicates a software programming bug. In a moment, the system reboots normally. System booting after fatal error FATAL: This can be caused by UPA address parity errors, Master queue overflows or DTAG parity errors.
Do you have a Creator3D card on the machine? So, a few null modem pinouts later, I have a connection to the serial port. No such device (ENODEV): An operation was attempted on an inappropriate or nonexistent device. http://nzbsites.com/solaris-10/solaris-10-netstat.html An example of such a system is a "headless" system that is not using a graphics display.
ROOT LOGIN ...: Someone has just logged in as root or su-ed to root. Timeout waiting for ARP/RARP packet: Indicates a network connection problem while booting from the network. Don't settle for less, sign up for your freeaccount today. type: boot Jeff Buddington
The following error message is displayed./[email protected]/[email protected]: Device 1c Nothing there /[email protected]/[email protected]: Device 1d Nothing there /[email protected]/[email protected]: Device 1e Nothing there /[email protected]/[email protected]: Device 1f Nothing there Probing I/O buses Sun Fire T200, I found that the best way for *me* was to dig out my old Gentoo 1.4 cd, although I believe the 2005.0 disc worked as well. Use a soft link instead. Latest 4.17.1 OBP was installed (but no real benefit there on the SB1500) BUT setting the boot env to use cdrom disk net and then power off the system (remove plug
tar: tape write error: A physical write error has occurred on the tar target. Thanks Ken Join this group Popular White Paper On This Topic Big Data and the CMO: An Introduction to the Challenge and the Opportunity 9Replies Best Answer 0 Mark this reply Regards. The output will include an expression, a source file number and a code line number.
The requested protocol does not support the requested socket type. I attach the output of prtconf -p -v System Configuration: Sun Microsystems sun4u Memory size: 1024 Megabytes System Peripherals (PROM Nodes): Node 0xf00296ec boot-retained-page: banner-name: 'Sun Fire V240' model: 'SUNW,375-3149' idprom: In the mean time its a cross between frirware upgrade so go back to the firware release before and tell me if you can boot. Booting Linux...
Mail is the world's favourite email. Patrick there might still be an issue with silo starting from cdrom. This error indicates a software bug. Connection refused (ECONNREFUSED): The target machine actively refused the connection.
© Copyright 2017 nzbsites.com. All rights reserved.